Force Hatching Eggs

GWLANG at ccmail.monsanto.com
Sat, 24 Aug 1996 01:14:53 -0500

A few days back Roy mentioned using "forced hatching" methods of
the killifish crowd. I though I might elaborate upon that a bit
further for those of you that are unfamiliar with the methods.
Since he didn't say which method or methods he used I'll go over
4 methods that have worked for me and more importantly worked
when I've had stubborn rainbowfish eggs, especially the
Pseudomugils. The others I really haven't had troubles with but
if you have a problem maybe one of these methods will help. I
really didn't look to see if anyone has been able to explain this
scientifically, I've seen carbon dioxide, pH, osmotic pressure,
feeding stimulation etc., all used as a reason for why the
various methods work. I would suggest to you that you might
practice on some of your own eggs before you get something
precious that you just have to hatch.

1) Microworms - Don't ask me how it works, I followed what was
set down by others and it worked for my killifish, and later for
my rainbowfish eggs, especially the Pseudomugils. Place the eggs
in a very shallow container, and cover the eggs with about 1/2 cm
of water, dechlorinated of course, tank water is fine for this.
Then remove a small amount of microworms from a very healthy
culture. Wipe them off the sides of the culture, don't bring any
of that baby food junk etc., into the hatching tray. It really
doesn't take many worms, maybe 10 or so per egg. Is it feeding
response, digestion of the egg sac, I don't know, but it does
work for a certain percentage of the eggs, if they were really
ready to hatch. After 5-6 hours though I'd remove any extra
worms and change the water in the hatching tray. You can wait
another day or move onto the next forced hatched method.

2) Carbon dioxide or just a lower pH, I'm not sure what does it
but get a piece of airline tubing and start blowing bubbles into
you tray of eggs. If you want to check on exactly how long it
will take your water to change pH take a similiar amount of
water, and add a few drops of bromothymol blue (your basic pH
indicator that you buy at the pet store) to it. It should be a
nice blue or aquamarine color in the beggining. When it changes
to very light green or yellow that's enough. Depending on the
hardness of your water (KH) it could take less than a minute to
several minutes. If you're over 400 ppm GH, probably with a KH
to match, you're not going to get anywhere fast. If your water
is that hard though that's probvably the reason your eggs aren't
hatching (cyanodorsalis excluded, of course). Then go back and
do a little heavy breathing into your batch of eggs. If that
doesn't get them to hatch in an hour or so change the water and
try another method.

3) Jiggles - put your eggs in a vial and take them to work, to
the grocery etc. Only fill the vial about 1/2 way so that there
will be air in the vial in case some fry hatch and you have a
ways to go before you get home. Don't try this while jogging :-)

4) Pressure - glass vials are better for this. Fill the vial
with your eggs and water. You want to make sure that the vial
will sink. Drop it into your 55, 110 gal etc. tank, whatever is
deeper. The lid is on loosely so that the pressure increase will
transfer to the eggs. I didn't use this techniques very often so
I'm not as familiar with it. I've had eggs hatch in a couple of
hours using this method.

If all else fails then you probably need to incubate them a bit
longer. I would suggest always using some shell grit in the tray
while you're incubating eggs. Even people with hard water have
reported better hatches when they add shell grit.

Gary Lange
RSG/ANGFA